Consider covering: In some cases, if the Artex ceiling is undisturbed and in good condition, covering it with panelling or skimming with plaster might be an option. It allows the removal of textured coatings such as Artex without causing dust from the harmful asbestos fibres, or just dust which can also be dangerous to inhale if removing large areas. It was formulated by Eco Solutions from the most advanced, innovative water-based technology using “science not solvents”. X-Tex Removal Solution is:

It may require a little bit more elbow grease on your part, but you should be able to get the job done! On the other end of the spectrum, the report by Barclays also names and shames the worst home faux pas in the country. You should apply at least 2 coats of paint to give a good finish, however you can add a third finishing coat if you wish. What if I Want to Remove Artex? Advocates of the various techniques for removing woodchip wallpaper swear by their various methods. Here are the most common:

Artex is a brand name and there are different patterns that can be made using it, some of these include: Results found that over a third of Brits weren’t happy with their home, and a quarter weren’t pleased from the moment they moved in.

Preparing Painted Surfaces: If the surface you’re artexing has been painted with an emulsion paint then you can artex straight over it (after wiping away any dust, debris and grime). However if there is satin paint on the surface then you will need to sand the whole area over using a medium grit 120 – 240 grit sandpaper first. If the existing paint colour is dark then to prevent any colour-bleed through the artex, over paint it with white emulsion first Ceiling cladding: Using PVC or other suitable materials, ceiling cladding can be attached directly over the Artex. It provides a clean, durable, and low-maintenance finish. There are 3 main ways you can cover an Artex Ceiling or Wall without the need for plastering. If you have any further suggestions let us know in the comments below. It is also the easiest to apply as long as you use an Artex texturing brush which should be covered with a polythene bag before painting on the Artex. We are a world-leading technology and innovation-driven company that has developed internationally leading-edge water-based paint strippers, coatings removers and associated products.

Preparing the Wall after Removing Woodchip or Textured Wallpaper

Note: wet plastering is a challenging skill that takes years to perfect, so I highly recommend hiring a professional plasterer to do the steps below. Artex is associated with asbestos and until 2000 Artex and other textured wall coverings contained asbestos which is a dangerous substance. Asbestos is a term for a group of minerals made of microscopic fibres, which if inhaled can damage your lungs and cause other serious diseases immediately or in the long term if exposed to it. Artex can be a dangerous substance, especially when it comes in powder form, as there is the risk of it containing asbestos, which may be a possibility if removing old Artex. If this is the case, you need to be extremely careful when removing it and may wish to hire a professional for extra safety.

To simplify plastering and improve the final finish, sand the surface until it’s flat and smooth. I recommend using 220-grit sanding paper. All you require is a smoothing knife and a tub of filler and you can get to work. I have included our choice of filler below. But home sustainability doesn’t mean solar panels, wind farms and going off-grid, it can be as simple as ensuring your home is energy efficient. This can be done with regular old emulsion, but if you want to try and get the best results on a budget, then you could opt for something like a Filler Coat Paint. It will need to be built up in layers, for the best results. Leaving 6 hours for the filler to dry between each layer.You can add some wallpaper remover or soap to the water which help loosen the glue even more. Start the steamer before you do this as they take quarter of an hour or so to warm up, which is about how long it will take to sponge down. Cover the narrowest width of the room first, if there is one, then work your way across in stages, applying the artex mix and then adding the textured finish. Carefully blend in each join between working areas so that when you are finished you have an even pattern covering the whole ceiling. Step 5 – Finish Around Edges

On discussing what home trends he dislikes himself, the property expert reveals: “Ugly blinds, fake beams, artex ceilings, wood chip, – unfortunately, they’re all quite hard to get rid of and can be costly and difficult to change.

Try covering the surface with foil or cling film and this helps to keep the product wet whilst it is working its magic There are many different chemical removal products on the market which can be used to help soften and help with the removal of both wallpaper and Artex. Products include Zinsser concentrated wallpaper stripper, X-Tex Artex removal or Fuze Durostrip Artex removal. These will help to loosen the coating and make it easier to strip off the wall. Like the wallpaper steaming option, this still involves a lot of hard work to remove the covering. Textured wall and ceiling coverings are no longer an interior design trend and will make a home look dated even if it is freshly painted. Most people now like smooth plastered walls and ceilings or wallpaper. If you are selling your house and you have textured coatings then you should seriously think about removing them and giving it a fresh coat of paint before you put it on the market. I wouldn't recommend it. There's far too much air and space under where the artex textures are. So it easily moved over time.